Buscar en el sitio
Button Pad 4x4 - Breakout PCB
https://www.microjpm.com/products/button-pad-4x4-breakout-pcb/
tion: This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the connector leads on the button side as short as possi
Especificación 220,1 kB
SparkFun Level Shifting microSD Breakout [DEV-13743]
https://www.microjpm.com/products/sparkfun-level-shifting-microsd-breakout/
ant for ease of use, discrete level shifting is no longer required. This breakout is also a bit unique in that it level translates all of its outputs back to the level of the hardware it’s connected to. Documents: Schematic Eagle Files Hookup Guide
Especificación 221,1 kB
Coin Cell Battery Holder - 2xCR2032 (Enclosed)
https://www.microjpm.com/products/coin-cell-battery-holder-2xcr2032-enclosed/
l run batteries in series, output up to 6V, and is equipped with an On/Off slide switch and two 6" power wires (one positive and one negative) on the back. Para más detalles ver el siguiente enlace: www.sparkfun.com/products/12618 Etiquetas : P
Especificación 218,6 kB
Piezo Vibration Sensor - Small Horizontal [SEN-09198]
https://www.microjpm.com/products/ad33639/
quencies. Useful for detecting vibration and ‘tap’ inputs from a user. A small AC and large voltage (up to +/-90V) is created when the film moves back an forth. A simple resistor should get the voltage down to ADC levels. Can also be used for imp
Especificación 219,8 kB
Bluefruit LE SPI Friend - Bluetooth Low Energy (BLE)
https://www.microjpm.com/products/ad28815/
happy to use the standard Nordic UART RX/TX connection profile. In this profile, the Bluefruit acts as a data pipe, that can 'transparently' transmit back and forth from your iOS or Android device. You can use our iOS App or Android App , or
Especificación 223,8 kB
Teensy Header Kit [PRT-13925]
https://www.microjpm.com/products/ad27436/
ader 1x 7-pin female header (for pins on end) 1x 3-pin header (for 3-off grid holes) 1x 2x7 right-angle SMT header, for the surface mount pads on the back of the Teensy 3.2 Para más detalles ver el siguiente enlace: www.sparkfun.com/products/13925
Especificación 219,5 kB
Button Pad 4x4 - Breakout PCB
https://www.microjpm.com/products/button-pad-4x4-breakout-pcb/
tion: This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the connector leads on the button side as short as possi
Especificación 220,1 kB
Adafruit RFM69HCW Transceiver Radio Breakout - 868 or 915 MHz [PID:3070]
https://www.microjpm.com/products/adafruit-rfm69hcw-transceiver-radio-breakout-868-or-915-mhz/
ver you like, and any other modules tuned to that same frequency (and, with the same encryption key) will receive. The receiver can then send a reply back. The modules do packetization, error correction and can also auto-retransmit so its not like yo
Especificación 225,3 kB
Thermal Printer [COM-14970]
https://www.microjpm.com/products/thermal-printer/
fit into the printer. But, you can always use the excess paper in the printer, since you don't need to have a 'core' in the paper for it to work. The back panel has 2 3-pin connectors; one for power and one for serial communications. The thermal prin
Especificación 221,8 kB
TDA8954 2 x 210W Class-D Power Amplifier
https://www.microjpm.com/products/ad37717/
o ±42.5 V and features low quiescent current consumption. The TDA8954 is supplied with two diagnostic pins for monitoring the status of Thermal Fold Back (TFB), Over Current Protection (OCP) and other protection circuits. Para más detalles ver hoja
Especificación 217,9 kB
Elementos: 21 - 30 de 80